TPM 088/12 - rev.2 - Valid from 01.12.2025
¶ MANDÍK AIR HANDLING UNITS
Modular air handling units designed for central air distribution and treatment in industrial and commercial applications. They provide air conveyance and treatment with a high level of operating efficiency. They are manufactured with air flow rates from 500 to 200 000 m3/h. The units are fully manufactured and certified in a unique frameless design. The high variability of configurations enables customized solutions.
¶ 1. GENERAL INFORMATION
¶ 2. RELATED DOCUMENTS
¶ 2.1. COMMON DOCUMENTS
¶ 2.2. KJM-SPECIFIC DOCUMENTS
¶ 3. UNIT IDENTIFICATION
¶ 4. SAFETY
The unit must be installed in an access-controlled area.
¶ 4.1. COMPLIANCE WITH LEGISLATION AND STANDARDS
4.1. COMPLIANCE WITH LEGISLATION AND STANDARDS
¶ 4.2. GENERAL SAFETY INSTRUCTIONS
4.2. GENERAL SAFETY INSTRUCTIONS
¶ 4.3. PED DIRECTIVE - 2014/68/EU
4.3. PED DIRECTIVE - 2014/68/EU
The units may contain pressure parts that fall within the scope of Directive 2014/68/EU (PED). In such cases, the provisions of the Pressure Equipment Directive apply to the relevant equipment (see the EU Declaration of Conformity).
¶ 4.4. NOISE EMISSIONS AT THE OPERATOR POSITION
4.4. NOISE EMISSIONS AT THE OPERATOR POSITION
¶ 5. HANDLING, TRANSPORT AND STORAGE
5. HANDLING, TRANSPORT AND STORAGE
¶ 6. ASSEMBLY AND INSTALLATION
¶ 6.1. GENERAL
• CAUTION: The gas heater burner must only be adjusted after it has been installed on the chamber.
¶ 6.2. UNIT PLACEMENT
¶ 6.3. GENERAL UNIT ASSEMBLY
¶ 6.4. INSTALLATION OF ACCESSORIES AND AIR DUCTS
6.4. INSTALLATION OF ACCESSORIES AND AIR DUCTS
¶ 6.5. MAIN ELECTRICAL SWITCH AND DISCONNECTION OF THE UNIT FROM THE POWER SUPPLY
6.5. MAIN ELECTRICAL SWITCH AND DISCONNECTION OF THE UNIT FROM THE POWER SUPPLY
¶ 7. COMMISSIONING
¶ 7.1. GENERAL PRE-COMMISSIONING OPERATIONS
7.1. GENERAL PRE-COMMISSIONING OPERATIONS
¶ 7.2. COMMISSIONING OPERATIONS
¶ 7.3. OPERATOR TRAINING AND UNIT HANDOVER
7.3. OPERATOR TRAINING AND UNIT HANDOVER
¶ 7.4. COMMISSIONING CONDITIONS
¶ 8. OPERATION AND MAINTENANCE
¶ 8.1. COMMON INSTRUCTIONS
¶ 8.2. COMMON MAINTENANCE INTERVALS
8.2. COMMON MAINTENANCE INTERVALS
¶ 9. INDIVIDUAL BUILT-IN COMPONENTS - DESCRIPTION, ASSEMBLY AND INSTALLATION, COMMISSIONING, OPERATION AND MAINTENANCE
¶ 9.1. FAN CHAMBER
¶ 9.2. FILTER CHAMBER
¶ 9.3. PLATE HEAT EXCHANGER CHAMBER
9.3. PLATE HEAT EXCHANGER CHAMBER
¶ 9.4. ROTARY HEAT EXCHANGER CHAMBER
9.4. ROTARY HEAT EXCHANGER CHAMBER
¶ 9.5. WATER, CONDENSER AND STEAM HEATER CHAMBER
9.5. WATER, CONDENSER AND STEAM HEATER CHAMBER
¶ 9.6. ELECTRIC HEATER CHAMBER
¶ 9.7. GAS/OIL HEATER CHAMBER
¶ 9.8. MONZUN HEATER CHAMBER
¶ 9.9. WATER COOLING COIL CHAMBER
9.9. WATER COOLING COIL CHAMBER
¶ 9.10. EVAPORATOR CHAMBER
¶ 9.11. LIQUID-CIRCUIT HEAT RECOVERY (ZZT) CHAMBERS
9.11. LIQUID-CIRCUIT HEAT RECOVERY (ZZT) CHAMBERS
¶ 9.12. INTEGRATED HEAT PUMP COMPRESSOR CHAMBER
9.12. INTEGRATED HEAT PUMP COMPRESSOR CHAMBER
¶ 9.13. SILENCER CHAMBER
¶ 9.14. DAMPER CHAMBER, END PANEL AND CHAMBER WITH DAMPER IN GENERAL
9.14. DAMPER CHAMBER, END PANEL AND CHAMBER WITH DAMPER IN GENERAL
¶ 9.15. HUMIDIFIER CHAMBER - STEAM / ADIABATIC
9.15. HUMIDIFIER CHAMBER - STEAM / ADIABATIC
¶ 9.16. UV LAMP CHAMBER
¶ 10. ANNEXES
The annexes for the air handling unit are: